Standard Work · October 2026

Halbury Seating Ltd

Upholstered dining and lounge chairs made to order for hotels, restaurants and care homes. 28 staff. The job: upholster a drop-in seat pad (the most common job in the shop).

Worked example. Halbury Seating and its figures are fictional. All figures come from the worked-example spreadsheet: ALL CHECKS PASSED (with 3 notes).
The headline

A seat takes 613 seconds today; the best repeatable way takes 510

Net saving
£21,926
a year, after £646 of audits; payback about 1 month on £1,742
Hours freed
951
a year; 480 cut overtime, the rest is capacity
People needed
4.1 → 3.4
at takt 150 seconds; 4 do the job today
Most time lost
22s
a seat, at the corners

Verdict: 12 steps written down. A job takes 613 seconds on average today and 510 on the standard, a gap of 17%; takt is 150 seconds, so the job needs 4.1 people today and 3.4 on the standard, against 4.0 doing it. Most time is lost at: fold and staple the corners (22 seconds a job). Closing 50% of the gap, with fewer mistakes and quicker training, frees about 951 hours a year; 480 of them cut overtime and the rest is capacity, not money. The net saving is £21,926 a year after £646 of audits, for £1,742 one-off (payback 1 month).

Where the time goes

The same job, five different ways

Timed 5 to 9 October 2026: one cycle from each of five upholsterers (A to E), by the works manager with a stopwatch. Each bar is the standard for that step; the red tick is today's average; the grey line runs from the quickest to the slowest person.

1. Take base board and foam from the ki…26s2. Glue foam to the board46s3. Wait for the glue to tack60s4. Cut wadding to the template31s5. Position the fabric, pattern aligned41s6. Staple the front and back centres20s7. Staple the sides, pulling evenly91s8. Fold and staple the corners82s9. Trim the excess fabric36s10. Fit the bottom cloth40s11. Check against the master sample and …20s12. Place on the despatch trolley16sStandard: workStandard: walking or waitingAverage todayQuickest to slowest

The biggest differences are at the corners, positioning the pattern and fetching parts. The quickest upholsterers fold every corner the same way, use the centre marks, and take parts from the kit trolley; those are now key points. The quality check is the one step where quicker isn't better: its standard is set at 20 seconds. Waiting for glue is a fifth of the job: written down as it is, and a target for the next round of improvement.

The standard

Upholster a drop-in seat pad

#StepKey pointsWhy it mattersSecondsRunning total
1Take base board and foam from the kit trolley
Walking
Take from the kit trolley, not the racksThe trolley is kitted for the day's order2626
2Glue foam to the board
Manual work
Glue only inside the marked zone
Safety: Extraction on before spraying
Glue outside the zone shows through thin fabrics4672
3Wait for the glue to tack
Waiting
Touch test at the corner: tacky, not wetWet glue soaks through; dry glue doesn't hold60132
4Cut wadding to the template
Manual work
Use the template for the seat size on the job cardToo much wadding makes the corners bulky31163
5Position the fabric, pattern aligned
Manual work
Pattern centre mark on the board's centre markA misaligned pattern is the main reason seats are re-covered41204
6Staple the front and back centres
Manual work
One staple each, 10 mm from the edge
Safety: Staple gun pointed down, fingers clear
Fixes the pattern before the sides are pulled20224
7Staple the sides, pulling evenly
Manual work
Work from the centre outwards, staples 25 mm apart
Safety: Staple gun pointed down, fingers clear
Uneven pull wrinkles the fabric91316
8Fold and staple the corners
Manual work
Two pleats each corner, folded towards the backCorners must match across a set of chairs82398
9Trim the excess fabric
Manual work
Trim 15 mm outside the staple line
Safety: Cut away from the body; knife back in its holder
Too close and staples pull through36434
10Fit the bottom cloth
Manual work
Bottom cloth square to the front edgeHides staples and keeps dust out40474
11Check against the master sample and label
Checking
Pattern alignment and corner pleats against the master sampleCatches a fault before the seat is fitted to a frame20494
12Place on the despatch trolley
Walking
Face up, label to the frontAssembly picks seats by label16510

Tried by all four upholsterers for two weeks before it was fixed. Printed at each bench with the master sample; audited every fortnight by the works manager, who times one seat and checks the key points.

What it's worth

Hours freed are money only where they cut overtime

SourceHours a year
The method: closing 50% of the gap in work to the standard (waiting for glue isn't counted)545
Fewer seats re-covered (3.5 → 1.5 per 100)331
Quicker training for 3 new starters (senior upholsterers' time: capacity, not overtime)75
Total: 480 cut overtime at £31.50 an hour (£15,120); 471 are capacity, not counted951
Plus fabric saved on seats not re-covered£7,452

The capacity is real but worth money only if Halbury sells more seats or avoids a hire: with 3.4 people needed on the standard, the fourth upholsterer's spare time could go to lounge chairs, now made on overtime.

How confident are we?

What this rests on

Times are from 60 timings of real jobs across 12 steps. The standard is the average of the two quickest times for each step unless set by hand: the best repeatable, not the best ever. Only 50% of the gap is assumed to close. Hours freed count as money only up to the overtime or agency hours they can cut, at the overtime rate; the rest is capacity. The mistake rate after, and training hours after, are estimates until counted. Waiting steps are timed but not counted as hours saved. Writing and auditing time is costed at the full hourly cost.